Skip to main content

BriefCam Administrator Guide

Permissions

Last Updated: 5 minute read

Camera Permissions

Caution

This functionality is not applicable for the Hub. It is only relevant for sites and in standalone deployments.

By default, every user has permissions for every camera via the Everyone group.

If you want to only allow certain users and/or groups to access cameras:

  1. In the left-hand pane, click on Users & Groups.

  2. Go to the Groups section (on some screen resolutions, you may have to scroll down to the Groups section).

  3. From the Everyone group, click on the permissions icon (Group permissions icon.png).

    Group permissions 64.png

  4. In the Group Permissions screen, go to the Cameras section and click on the edit icon.

    Group permissions cameras.png

  5. Delete the asterisk by clicking on the trash can icon to the right of the asterisk (*).

    Cameras delete asterisk.png

  6. Click Close and then click Close again.

  7. From the Users & Groups section, click the permissions icon for a user or group and add the cameras that a user or group has permissions to view by clicking Add Camera name or Directory path (as seen in the image above). Cameras can be defined by a VMS path or by a camera name. An asterisk (*) can be used in any part of the path or camera name. For example, /Division1/Department1* gives access to all cameras in the Division1 folder whose names begin with Department1. Another example: Axis* gives access to all cameras whose names begin with Axis.

  8. If you want to further limit the access with read/write permissions, from the Camera Management section, assign the relevant camera/s to each user or group by clicking the permissions icon for each user and/or group. Below is additional information about camera-based permissions.

Camera permissions on screen.png

When more than one camera is selected, you can click the permissions icon in the top right corner of the screen to assign permissions to multiple cameras simultaneously.

Camera permissions bulk.png

Note

Applying permissions to multiple cameras simultaneously overwrites any permissions previously assigned to these cameras.

When you click the permissions icon for a camera, the following screen will appear where you will see the users and groups who have permissions for this camera.

When you apply permissions to a group of cameras simultaneously, this dialog will be empty.

Camera permissions screen.png

Click the Add group or user button to open the following screen. Click on a user or group, select the rights that you want to assign for that particular user or group and click the Apply permissions button.

You need to click the Apply permissions button for every user or group that you define permissions for.

Permissions users and groups.png

When you assign a Write permission, the user/group can create camera-derived entities, such as processing requests or creating sources from this camera. When you assign a Read permission, the user/group can see if the camera exists and get its original video or live stream.

User/Group Permissions

Caution

This functionality is not applicable for the Hub (except for the Allow Access to RESPOND checkbox). The rest of the functionalities are only relevant for sites and in standalone deployments.

BriefCam allows you to define a set of permissions per individual user or group.

Click the user permissions icon Permissions icon.png or the groups permission icon Group permissions icon.png to assign permissions for the following three items:

If the user has one or more permissions, a green dot will appear next to the permissions icon, either Permissions icon green.png or Group permissions icon green.png.

Network Access Path

Note

Network paths are only supported for the following BriefCam platform editions: Investigator and Protect. If you have the Rapid Review or Insights edition, network paths are not supported.

The network paths that this user has permissions to access.

Note that to enable the Network tab, set the clientEnableTabNetwork environment setting to true.

An asterisk (*) must be added at the end of the path to give full access to that folder any of its subfolders and files.

If you want to give permissions to a specific subfolder, the full path needs to first be defined in the UploadedVideoLocations environment setting.

For example, if you have a departments folder that includes two subfolders: department1 and department2. And you only want to allow user1 access to the department 1 folder and allow user2 access to both folders, do the following:

  1. In the UploadedVideoLocations environment setting, define two separate paths: \\departments\department1 and \\departments\department2. This is what the JSON file should look like in the setting:

    JSON Editor 2.png

  2. In the Users & Groups screen, click the permissions icon for one of the users. In the example below, the icon is marked for user1 (a user defined for this example).

    Permission icon on screen.png

  3. Select the Network Access Path checkbox and click the edit Edit icon white.png icon.

    Network access path.png

  4. In the Add Network Path field, enter the path to department 1: \\departments\department1* (there is no need to double the slashes like we did in the JSON file).

  5. Make sure to click the check mark to apply permission.

    Network access path check.png

  6. When adding a new video file to a case, in the Network tab, user1 will be able to see all of the folders and files in the department1 folder.

  7. For user2, click the permissions icon and add the following network path: \\departments*

  8. In the Network tab, user2 will be able to see both folders (department1 and department2) and their subfolders and files. But, user2 will not be able to see, for example, department3 unless it’s defined first in the environment setting.

See also: NAS Configuration 

View External Watchlists

The external watchlists that this user has permissions to view.

Cameras

The cameras that this user has permissions to view. Cameras can be defined by a VMS path or by a camera name. An asterisk (*) can be used in any part of the path or camera name. For example, /Division1/Department1* gives access to all cameras in the Division1 folder whose names begin with Department1. Another example: Axis* gives access to all cameras whose names begin with Axis.

For additional information, see the Camera Permissions section.